Active Ferrite Antenna .5 - 2.5 MHz For Icom IC-R20 AOR AR8200 Alinco DJ-X11*

$66.47 $94.95

In Stock
  • Estimated Delivery:Jul 10 - Jul 17

  • Free Shipping & Returns: On all orders

Guarantee safe & secure checkout

  • Free Shipping & Returns or all orders over
  • Secure Payment We ensure secure payment
  • Money Back Guarantee Any back within 30 days
This sale is for an active (amplified) receive HF ferrite antenna for your handheld wideband radio receiver covering the frequencies from 500 KHz - 2.5 MHz.  The handheld radio shown in the picture above is used for demonstration only and is NOT included with the antenna.  Please note that the picture shows a sample of this series of antennas, but not the correct frequency range of 500 KHz - 2.5 MHz which is what is being sold in this listing. If you have a handheld wideband radio receiver, you will typically notice that the unit will work well on the upper bands (30 MHz and upward) in the FM, VHF, and UHF frequencies.  However, while most handhelds can receive the medium wave and shortwave frequencies, reception is less than optimum and can be outright very poor when using the supplied manufacturer antenna.  If you are like us, you have replaced the original Rubber Duck or telescopic whip antenna with other variations trying to improve HF performance in the MW and SW bands.  We have even traveled with a small bag to carry more than one antenna to swap in for such purposes.  However, despite this, you will find reception to be suboptimal or even very poor. This active ferrite antenna was designed to offer an alternative for mediumwave and lowband HF reception from 500 KHz - 2.5 MHz to enable you to grab those signals from your favorite mediumwave broadcast station or 160 meter net.  Reception on the mediumwave and amateur 160 meter with this antenna is much better and you can typically copy many more signals that would otherwise be unavailable using the antenna supplied by the radio's manufacturer.  During our testing, we discovered a large difference between the stock antenna and what this active ferrite antenna could deliver.  Receive signals were stronger, and signals missed with standard antennas, were heard and copyable.   The antenna uses a BNC connector that is common on handheld scanning radios.  If your handheld does not have a BNC connector, you may be required to purchase a SMA to BNC adapter to use this antenna and such an adapter is available elsewhere here on Ebay.  The active ferrite uses a 23A alkaline battery which will provide approximately 65 hours of operation and which is supplied with the antenna.  Extra batteries are available from our Ebay store or elsewhere here on Ebay. To operate the antenna, you press the button on the top to power it on.  An LED illuminates to indicate the power status and then you merely turn the knob to peak the signal. Please note that this is a "RECEIVE ONLY" antenna and cannot be used with a handheld unit that transmits a signal.  You will be required to retain your original receive antenna for use on the higher bands such as 2.5 - 30.0 MHz HF
FM / VHF / UHF or purchase additional active antennas for the higher frequencies as available in our Ebay store. Here is a list of features for this active antenna:
Frequency range 500 KHz - 18.0 MHz
Very high gain & very high sensitivity
Sharp tuning also acts as front end filter
Low noise 200mm ferrite
Low power consumption draws ONLY 0.7 mA 
Operates 65 hours before battery replacement
On / Off switch
LED power indicator
BNC connector
Low noise circuit includes FM broadcast rejection (great performance in high signal areas such as cities)
SMD design
Directional to peak and null signalsBecause this is an active antenna, it is subject to much RF noise found in the household such as lighting, computers, TV's etc.  While it can be used in many households, we have found it works much better outside for that daily stroll, walking the dog, trip to the park, or hike in the mountains.  During testing, we noticed a nice signal improvement and the meter on the handheld displayed a stronger signal than any other factory we attempted to use.  Your results may vary depending upon the brand and model of handheld and what antenna you had previously utilized. Some examples of handheld radios that may use this antenna:
Icom IC-R10
Icom IC-R20
AOR AR8200
Alinco DJX-2000
Kenwood TH-D74
Yaesu VR-500
Yupiteru MVT-9000
any other wideband handheld that receives HF signalsHere is a video demonstrating the active ferrite in operation:
Please use the Ebay shipping calculator to determine your shipping cost.  This cost includes proper packing materials for safe delivery and insurance cost against damage or loss.
Those buyers living outside the USA are also welcome to purchase from us.  We have shipped to 105 countries during the past 22 years on Ebay and we are happy to ship virtually anywhere in the world.  You may use the shipping calculator to determine your shipping cost via either priority or express mail.
Please keep in mind that this cost does not include any import, customs, or VAT fees.  If you are uncertain of these costs, we ask you to check with your local post office prior to making a purchase from us.  Thank you!
Thank you for taking the time out of your busy day to look at our Ebay items!

Submit Your Review

Your email address will not be published. Required fields are marked *

1 2 3 4 5